Skip to content

Your cart is empty

Have an account? Log in to check out faster.

Continue shopping

How to Size an LED Wall: Panels, Resolution & Power

Divide target width and height by the cabinet size and round up. A 3 x 2 m wall from 500 mm panels is 6 across by 4 down, 24 panels. Resolution is width in millimetres divided by pitch: 3000 / 3.9 gives 769 pixels across.

The four calculations

Sizing a wall is arithmetic, not judgement. There are four numbers and they follow from each other.

1. Panel count

panels across = ceiling(target width / cabinet width)
panels down = ceiling(target height / cabinet height)

Round up, always. A wall is built from whole panels, so the finished size is almost never exactly the target. Decide early whether you are rounding the wall up past your target or accepting a slightly smaller wall.

2. Finished size

finished width = panels across x cabinet width

A 3 m target with 960 mm cabinets gives 4 panels across, so the finished wall is 3840 mm — 840 mm wider than asked for. If the stage cannot take that, the cabinet size is wrong for the design.

3. Resolution

pixels across = finished width in mm / pixel pitch in mm

This is the number your content and your processor care about. A 3840 mm wall at 2.5 mm pitch is 1536 pixels across, which fits comfortably inside a 1920 x 1080 canvas.

4. Power

maximum load = maximum W per m² x wall area in m²

Use the maximum figure for electrical design. Average draw in normal content is typically around a third of maximum, and that is the figure a generator sees, but the distribution has to carry the peak.

Worked example: a 5 m x 3 m stage wall

Using 500 x 500 mm panels at 3.9 mm pitch:

  • Across: 5000 / 500 = 10 panels
  • Down: 3000 / 500 = 6 panels
  • Total: 10 x 6 = 60 panels
  • Finished size: 5000 x 3000 mm, exactly 15 m²
  • Resolution: 5000 / 3.9 = 1282 across, 3000 / 3.9 = 769 down
  • Pixel count: 1282 x 769 = about 986,000 pixels, which is under a 1080p canvas
  • At 800 W/m² maximum: 15 x 800 = 12,000 W, needing at least four 16 A / 230 V circuits at 3680 W each

That last line is usually the one that changes the design. Twelve kilowatts before a single lighting fixture is plugged in is a conversation with the venue, not a detail.

Aspect ratio

A 10 x 6 panel wall is 10:6, which simplifies to 5:3 — close to 16:9 but not identical. Content mastered at 16:9 will either letterbox or crop. Either pick a panel count that matches your content ratio, or decide in advance how the mismatch is handled.

For 16:9 exactly with 500 mm panels, 16 across by 9 down gives an 8 m x 4.5 m wall from 144 panels.

Before you hang anything

Weight and load figures on this page are drawn from product specifications and are given for planning only. Load ratings must be verified against the manufacturer’s load table and signed off by a qualified rigger, taking wind loading into account for any outdoor position. Electrical distribution should be designed and installed by a competent person.

A reference table for common wall sizes

These are worked out with the formulas above for 500 x 500 mm cabinets, which is the most common size in this range.

Target size Panels across x down Total panels Area Pixels across at 3.9 mm Max load at 800 W/m²
2 x 1.5 m 4 x 3 12 3.0 m² 513 2400 W
3 x 2 m 6 x 4 24 6.0 m² 769 4800 W
4 x 2.5 m 8 x 5 40 10.0 m² 1026 8000 W
5 x 3 m 10 x 6 60 15.0 m² 1282 12000 W
6 x 3.5 m 12 x 7 84 21.0 m² 1538 16800 W
8 x 4.5 m 16 x 9 144 36.0 m² 2051 28800 W

The last column is the one that ends most conversations. A 36 m² wall at maximum draw is 28.8 kW, which is a three-phase supply rather than a handful of sockets.

Weight: the second constraint

total weight = weight per m² x wall area

Panel weight is published per cabinet or per square metre. A wall at 30 kg/m² over 15 m² is 450 kg of panels before the structure, the cabling or the processor. Whether that hangs depends on the venue's rigging points and the structure between them, which is a question for a qualified rigger working from the manufacturer's load table.

Ground support is the alternative when flying is not possible, and it changes the floor plan because the structure needs a footprint and a safe working area behind the wall.

Data and power cabling

Panels chain both power and data, with a published maximum number of cabinets per chain. Exceeding it causes voltage drop at the end of a power run and signal problems at the end of a data run, and both present as intermittent faults rather than clean failures.

For a 10 x 6 wall, the usual arrangement is to run chains vertically in columns, which keeps runs short and makes a faulty column easy to identify. Confirm the maximum chain length for the specific panel before planning the layout, because it varies with panel power draw.

Building in tolerance

Real stages are not exact. Leave tolerance in two places: the physical opening the wall sits in, and the content canvas.

If the set opening is 5 m and the wall is exactly 5 m, assembly becomes a struggle. If the content is mastered at exactly the wall's pixel count, a single panel added later breaks the mapping. Decide the finished pixel map before content production starts and treat it as fixed.

Where the panels are

Cabinet dimensions and pitch for every panel are published on the product pages in Pro LED Screens, split into indoor and outdoor ranges. The LED video wall buying guide covers pitch, brightness and refresh selection.

A checklist before ordering

  1. Target dimensions, and whether rounding up or down is acceptable.
  2. Panel count and finished size from the cabinet dimensions.
  3. Resolution and aspect ratio, confirmed against the content pipeline.
  4. Maximum power load and the number of circuits that implies.
  5. Total weight and the rigging method, confirmed with a rigger.
  6. Processor pixel capacity against the finished resolution.
  7. Spare modules, power supplies and at least one spare cabinet.

Decision criteria

  • If the stage width is fixed, choose a cabinet size that divides into it cleanly.
  • If content is 16:9, aim for a panel count in a 16:9 ratio.
  • If power is limited, reduce wall area before anything else; power scales with area, not with pitch.
  • If the wall is flown, get the weight per square metre and the load path confirmed by a qualified rigger before ordering.

Run your own numbers with the LED wall calculator, or browse Pro LED Screens.

Sources

  • Cabinet dimensions used in the worked examples are taken from the LED panels listed in this store.
  • Power figures are planning estimates; confirm the maximum draw published for your specific panel.

Frequently asked questions

How do I calculate how many LED panels I need?
Divide the target width and height by the cabinet dimensions and round each up. A 3 m by 2 m wall from 500 mm panels is 6 across and 4 down, which is 24 panels.

How do I work out the resolution of an LED wall?
Divide the finished width in millimetres by the pixel pitch in millimetres. A 5000 mm wall at 3.9 mm pitch is 1282 pixels across.

How much power does a 15 square metre wall need?
At 800 watts per square metre maximum, 15 square metres is 12,000 watts. That needs at least four 16 A / 230 V circuits, each carrying about 3680 watts.

What if the panel count does not match my target size?
You round up and accept a slightly larger wall, or you choose a cabinet size that divides more cleanly into your target dimension. Walls are built from whole panels.

How do I get a 16:9 wall?
Choose a panel count in a 16:9 ratio. With 500 mm cabinets, 16 panels across by 9 down gives an 8 m by 4.5 m wall from 144 panels.

Sources & Methodology

Our editorial content is produced through hands-on evaluation and cross-referenced against established industry sources. We do not publish sponsored rankings or accept payment to feature products.

  • RTINGS.com — Objective audio measurements, ANC performance, frequency response data
  • SoundGuys — Lab-tested audio reviews and earbud comparisons
  • Manufacturer specifications — Official product datasheets and technical documentation from brand websites
  • Soundmali editorial testing — Hands-on evaluation by our team. Last reviewed: November 2026

Explore Soundmali

Premium Audio & Tech

Headphones, smartwatches and more — free shipping on all orders.

Shop All

More from Guides

Search