Choose an amplifier rated about 1.5 to 2 times the loudspeaker's continuous RMS rating, read at the actual load impedance. A 400 W 8-ohm cabinet wants 600 to 800 W per channel. Two of those in parallel present 4 ohms and double the requirement.
The guideline, and why it exists
The familiar advice is to use an amplifier rated between 1.5 and 2 times the loudspeaker's continuous power rating. It sounds like over-specification and it is not.
Music is not a continuous tone. It has peaks well above its average level, and reproducing those peaks cleanly needs instantaneous power the average figure does not describe. An amplifier that can only just meet the continuous rating runs out of headroom on every transient and clips.
Why clipping damages loudspeakers
When an amplifier runs out of voltage swing, the tops of the waveform flatten. A flattened sine wave is mathematically a sine wave plus a series of odd harmonics at higher frequencies, and in a passive two-way cabinet the crossover sends those harmonics to the high-frequency driver.
A compression driver designed to handle a modest share of the cabinet's power now receives sustained energy it was never rated for. This is the mechanism behind the rule of thumb that a small amplifier kills more tweeters than a large one.
Read the rating at your impedance
Amplifier power is quoted per channel at a stated load. The same amplifier might be rated 500 W at 8 ohms and 800 W at 4 ohms. Those are not alternatives, they are the same amplifier measured into different loads.
parallel impedance of two identical cabinets = cabinet impedance / 2
Worked example
- One 8-ohm cabinet, 400 W continuous: target 600–800 W at 8 ohms
- Two 8-ohm cabinets in parallel: load is 4 ohms, total continuous rating 800 W
- Target becomes 1200–1600 W at 4 ohms
- Three 8-ohm cabinets in parallel: 2.67 ohms, which many amplifiers are not rated to drive at all
Check the amplifier's minimum rated load before planning parallel cabinets. Driving below it is how amplifiers go into protection mid-show, or stop going into protection and fail instead.
Limiting and gain structure
Headroom only protects drivers if something stops the system using it as extra volume. Set the limiter from the loudspeaker's rating, not from the amplifier's, and set gain structure so the console's clip point arrives before the amplifier's.
A reference table
These figures apply the 1.5 to 2x guideline to common cabinet ratings. Read the amplifier's specification at the impedance in the second column, not at its headline figure.
| Cabinet continuous rating | Load presented | Target amplifier power per channel | Notes |
|---|---|---|---|
| 200 W at 8 Ω | 8 Ω | 300–400 W | Single cabinet per channel |
| 400 W at 8 Ω | 8 Ω | 600–800 W | Single cabinet per channel |
| 2 x 400 W at 8 Ω | 4 Ω | 1200–1600 W | Two cabinets in parallel |
| 500 W at 4 Ω | 4 Ω | 750–1000 W | Check amplifier is 4 Ω rated |
| 2 x 500 W at 4 Ω | 2 Ω | 1500–2000 W | Many amplifiers are not rated this low |
Why the ratings themselves are slippery
“Continuous”, “programme” and “peak” are three different numbers for the same cabinet, and they are often roughly double each other in sequence. A cabinet described as 800 W might be 400 W continuous, 800 W programme and 1600 W peak.
Apply the guideline to the continuous figure. Applying it to a peak figure produces an amplifier roughly four times larger than intended, which is an expensive way to misread a specification.
The same caution applies on the amplifier side. An amplifier quoted at a peak or bridged figure is not describing what it delivers continuously into your load.
Bridging, and when not to
Many two-channel amplifiers can be bridged, combining both channels to drive one load at higher power. The catch is that bridging halves the effective load the amplifier sees: a bridged amplifier driving 8 ohms is working as hard as it would driving 4 ohms per channel.
So bridging into 4 ohms is equivalent to 2 ohms per channel, which many amplifiers cannot sustain. Check the manufacturer's minimum bridged load before planning it, and treat bridging as a way to drive one demanding cabinet rather than as free extra power.
Damping factor, in proportion
damping factor = load impedance / amplifier output impedance
A high damping factor means the amplifier controls the driver's motion more tightly, which is audible in low-frequency definition. The figure is widely quoted and widely over-weighted: once it is comfortably above about 100, the speaker cable's resistance usually dominates anyway, which is another reason to size cable properly on long runs.
Thermal reality in a rack
Amplifier power ratings assume the unit can get rid of its heat. A dense rack with no airflow path pushes amplifiers into thermal protection, which presents as the system cutting out during the loudest part of the show and working perfectly during the sound check.
Leave ventilation space, keep intake and exhaust unobstructed, and remember that amplifiers draw substantially more mains current under real programme than their idle figure suggests.
A practical sequence
- Find the cabinet's continuous power rating and nominal impedance.
- Decide how many cabinets share each amplifier channel, and calculate the resulting load.
- Multiply the total continuous rating by 1.5 and by 2 to get a target range.
- Read candidate amplifiers at that exact impedance.
- Confirm the amplifier's minimum rated load is at or below your figure.
- Set limiting from the speaker rating, then set gain structure.
Published figures for the amplifiers in this range are on each product page in Power Amplifiers; cabinet ratings are in PA Speakers and Line Arrays, and processing options are in Signal Processors.
Decision criteria
- If you are between two amplifiers, take the larger one and limit it properly.
- If cabinets are paralleled, recalculate the impedance before reading any power figure.
- If the amplifier has onboard DSP, use its limiter rather than adding an external one.
- If you hear distortion and reach for more gain, stop: that is the failure mode, not the fix.
Published power and impedance figures for each unit are on the product pages in Power Amplifiers, and cabinet ratings are in PA Speakers. The PA system buying guide covers the whole chain.
Sources
- IEC 60268 covers power rating methods, including the distinction between continuous, programme and peak ratings.
- Amplifier and cabinet figures come from the product data published in this store.
Frequently asked questions
How many watts of amplifier do I need?
About 1.5 to 2 times the loudspeaker's continuous RMS rating, read at the load impedance you will actually present. A 400 W 8-ohm cabinet suggests 600 to 800 W per channel at 8 ohms.
Can an amplifier be too powerful for a speaker?
It is a smaller risk than being too small, provided limiting is set from the speaker's rating. A clipping amplifier damages high-frequency drivers far more reliably.
What impedance do two speakers present?
Two identical cabinets in parallel halve the impedance. Two 8-ohm cabinets present 4 ohms; three present about 2.67 ohms, which many amplifiers cannot drive.
Why does clipping damage tweeters?
A clipped waveform contains added high-frequency harmonics. The crossover routes those to the compression driver, which then receives sustained energy beyond its rating.
Where should I set the limiter?
From the loudspeaker's rating, not the amplifier's, so the headroom protects the drivers rather than becoming extra volume.